DAKING - FET III Agrandir l'image
Method of Limiting: FET (Field Effect Transistor) used as a variable resistor
Stereo Linking Method: Continuously Variable Audio Summing
Power: 48volts dc @ 150 ma
Output Drive: Differentially balanced +24dbv @ 1kHz 600 Ω
Ratios: 1.5:1, 2:1, 3:1, 5:1, 10:1, 20:1
Attack Times: 250 μs to 64 ms
Release Times: 500 ms to Auto Dual Time Constant
Frequency Response: ±1db 10Hz to 56kHz 3db down 63kHz
Noise: -82db 10Hz to 25kHz
Distortion: THD+N 0.033 @ 1kHz
Line Inputs: The XLR inputs are balanced with THAT Corporation differential amps. Up to +24dBu input.
Line Outputs: The XLR Outputs are balanced with THAT Corporation differential amps. Up to +24dBu output.

Plus de détails

DAKIBA827B

Nouveau

DAKING - FET III

Daking Audio

The Daking FET III is a dual channel limiter from Geoff Daking, built in the US with the same audio path and detector circuits as our highly successful single channel Daking FET II limiter. The FET III compressor circuitry and gain stages are all discrete and fully Class “A” with sound quality that will be at the very top of the scale. Our previous single channel FET II was known for its speed, high performance and its unique ability to sound great on an extraordinary variety of sources. The FET III will equal this benchmark plus add several unique features to improve user control. The differences are as follows:

New variable High Pass Filters from 0 to 200Hz are added to the detector stage of each limiter channel to improve and customize limiter behavior. The HPF’s tell the limiter NOT to trigger limiting based on content below the set HPF frequency. This is extremely helpful on bass heavy material. This greatly widens the units potential application set and the ability of the user to set this new behavior “on the fly”.

Variable linking between channels is envisioned for use when compressing two different tracks, such as bass and kick, to tie limiter action together to greater or lesser degrees. The Stereo Link is continuously variable from 0 to ∞.

All controls except “Ratio” are pots. The new variable pots add the ability to fine tune behaviors in the studio. Mastering engineers may prefer the repeatability of switches, such as those on the FET II, which will continue in the Daking product line.

The FET II’s relied on control voltage summing for the stereo linking. Because the FET III is two independent units in one box, it uses audio summing, which is much more accurate.

The Daking FET III uses THAT CORP differential amps in and out (electronically balanced). The FET II has transformers in and out but they are 1:1 input to output so they do not “color” the sound. (A mic input transformer at 1:10 ratio in a mic pre would color the sound significantly.) The common mode rejection in FET III is equal to that of FET II. The FET III output level is +24 while the FET II can be as high as +30.

The FET III and FET II both use an outboard power supply.

The unit is fully RoHs compliant.

Features And Specs

Method of Limiting: FET (Field Effect Transistor) used as a variable resistor
Stereo Linking Method: Continuously Variable Audio Summing
Power: 48volts dc @ 150 ma
Output Drive: Differentially balanced +24dbv @ 1kHz 600 Ω
Ratios: 1.5:1, 2:1, 3:1, 5:1, 10:1, 20:1
Attack Times: 250 μs to 64 ms
Release Times: 500 ms to Auto Dual Time Constant
Frequency Response: ±1db 10Hz to 56kHz 3db down 63kHz
Noise: -82db 10Hz to 25kHz
Distortion: THD+N 0.033 @ 1kHz
Line Inputs: The XLR inputs are balanced with THAT Corporation differential amps. Up to +24dBu input.
Line Outputs: The XLR Outputs are balanced with THAT Corporation differential amps. Up to +24dBu output.

Commander

DAKING - FET III

DAKING - FET III

Veuillez patientez...

Pour le moment, M2M Pro a choisi la relation directe avec ses clients.
Les ventes, demandes d'offres et prix... se font via ce formulaire.
N'hésitez pas à prendre contact avec nous pour toute autre question.












* Champ requis

ou